Byron Plumbers, Heating and AC Services

For this job, I came out and gave an estimate to install all new water lines. Customer would like for us to follow up with him next Wednesday to see what he would like to do. Waived dispatch fee due to the size of the estimate.

Found fuse blown upon arrival changed fuse after 5 minutes it blew again. Pulled y and common off of contactor fuse did not blow again therefore it was a bad contactor which we replaced with a new one the unit is working as it should be

Replaced motor as quoted

Found system with a bad x13 blower motor motor is under warranty but it will be tomorrow before we can do any thing with it due to getting parts

Upon arrival customer stated upstairs wasn’t cooling I walked out Sid checked capacitor checked to see if I was getting a call and checked to see if I had pressures everything was good but I noticed the board was giving a lockout code so I went to the air handler and reset the unit as soon as it reset i noticed that my head pressure was going up extremely high and shutting off the unit. So I checked all my voltage and I noticed I had a bad indoor txv so I gave customer some options on replacing it and customer would like to decline at this time

Reconnected reversing valve wire and hooked up new thermostat. Tested and working as it should

Replaced condensate pump, filled with water and tested. No leaks

Found that condensate drain line was kinked due to position. Repositioned and straightened out kink

Upon arrival customer stated unit was leaking in the closet, I walked to the unit and checked the condensate pump and the pump was working properly at this time them I checked the coil and the coils was dirty and was dripping water off of It, so I gave customer estimate on pull and clean and just in place cleaning. Customer approved in place cleaning, so I sprayed the coil. If this does not fix we will have to do a pull in clean if they approve.

Came here after Tony pumped tank. We attempted 93 or free and heard cable under house. I crawled under house and sewer is separated. I need to get with Jimmy on getting a price to fix this issue before we cable the sewer again.

Unstop toilet with closet auger .

Found that thermostat was energizing reversing valve which it should not be doing as it is a Rheem unit. Disconnected B and unit runs in cool mode. Will need to return with a basic thermostat to replace this bad one. However, unit is cooling for the time being as I left B disconnected

Unstop main sewer line .

Arivied and four outdoor fan running and compressor was not running checked all electrical and found bad capacitor. Homeowner approved replacing capacitor.replaced capacitor.and checked system operation.foun refrigerant pressure we’re right where they need to be. Customer decided to sign up for maintenance agreement. Also talked about adding a mini split upstairs, we need Jessie to come out.

For this job, we came out and replaced a Pumptrol well switch. Customers well is operational at this time. Customer requested for an itemized list for her home warranty company to reimburse her for the cost of the job. Customer and I both heard a leak under the kitchen sink behind the cabinet. Customer would like to call the home warranty company she currently uses as well. We are not liable if the well pump has failed, but will give options to replace it upon completion of job if necessary.

Found bad run capacitor and bad fan motor Replaced motor and dual run capacitor. All OPPs normal at this time All OPPs normal

Ashley’s number 8506039100 Return and do quoted repair

I arrived on site and greeted customer. I found the indoor unit was frozen solid. I defrosted the coil and found the coil was very dirty. I quoted cleaning coils so I could check pressures I found the system had no Freon it only had 50 psi.customer declined repairs at this time.

I arrived on site and greeted customer. I went to the unit and found the fan motor was still running. I then checked pressures and found they were low. I did a leak search (over 10 years old) and found the leak in the liquid line coupling at the evaporator. Customer requested we come back to do the repair another time.

Found ice maker shower high head pressure lockout . Checked condenser coil was clean problem was due to refrigerator was put close to vent on side of ice maker .this was making pressures high and causing machine to lock out.moved refrigerator away from ice maker . This made machine cycle as it should. Watched through four harvest cycles All OPPs normal

I arrived on site and greeted customer, I went to the outdoor unit and pumped it down, I then went to the air handler and removed the coil and then removed the bad TXV I then brazed in a new one under warranty and re installed the coil. I also mounted the bulb and insulated it. Then I pressure tested the system with nitrogen and found no leaks, I pulled a vacuum down to about 600 microns. I then released the charge back into the system and checked operation.

Replace capacitor and relay. Replaced start components as quoted All OPPs normal

Replace capacitor Replaced capacitor on carrier heat pump All OPPs normal

Upon arrival set thermostat to cool, checked annd removed dirty filter, and went to outdoor unit. Unit running but pressures were 30/284. Went to air handler and found that it had previously been frozen as insulation was wet. Went back to outdoor unit and switched it to heating mode outside. Pressures ran as normal. Put it back to cool and went to air handler and found that unit was freezing at TXV. Will need to determine if unit is under warranty before giving a correct price

Found that capacitor was dead upon arrival and customer stated he had put it on a few days ago however he had had it for a while. I tested unit with a working 45/5 and found no other issues. Fan motor is not over amping and works fine with working capacitor. Gave estimate to replace capacitor. Customer declined at this time. Left disconnect to not harm anything else as compressor is still getting a leg of power. Informed customer and he was okay with that and saw where I put disconnect plug